System calls and library wrapper functions¶

System calls are generally not invoked directly, but rather via wrapper functions in glibc (or perhaps some other library). For details of direct invocation of a system call, see intro(2). Often, but not always, the name of the wrapper function is the same as the name of the system call that it invokes. For example, glibc contains a function chdir() which invokes the underlying "chdir" system call.

Often the glibc wrapper function is quite thin, doing little work other than copying arguments to the right registers before invoking the system call, and then setting errno appropriately after the system call has returned. (These are the same steps that are performed by syscall(2), which can be used to invoke system calls for which no wrapper function is provided.) Note: system calls indicate a failure by returning a negative error number to the caller on architectures without a separate error register/flag, as noted in syscall(2); when this happens, the wrapper function negates the returned error number (to make it positive), copies it to errno, and returns -1 to the caller of the wrapper.

Sometimes, however, the wrapper function does some extra work before invoking the system call. For example, nowadays there are (for reasons described below) two related system calls, truncate(2) and truncate64(2), and the glibc truncate() wrapper function checks which of those system calls are provided by the kernel and determines which should be employed.

System call list¶

Below is a list of the Linux system calls. In the list, the Kernel column indicates the kernel version for those system calls that were new in Linux 2.2, or have appeared since that kernel version. Note the following points:

•

Where no kernel version is indicated, the system call appeared in Linux 1.0 or earlier.

•

Where a system call is marked "1.2" this means the system call probably appeared in a Linux 1.1.x kernel version, and first appeared in a stable kernel with 1.2. (Development of the Linux 1.2 kernel was initiated from a branch of Linux 1.0.6 via the Linux 1.1.x unstable kernel series.)

•

Where a system call is marked "2.0" this means the system call probably appeared in a Linux 1.3.x kernel version, and first appeared in a stable kernel with Linux 2.0. (Development of the Linux 2.0 kernel was initiated from a branch of Linux 1.2.x, somewhere around Linux 1.2.10, via the Linux 1.3.x unstable kernel series.)

•

Where a system call is marked "2.2" this means the system call probably appeared in a Linux 2.1.x kernel version, and first appeared in a stable kernel with Linux 2.2.0. (Development of the Linux 2.2 kernel was initiated from a branch of Linux 2.0.21 via the Linux 2.1.x unstable kernel series.)

•

Where a system call is marked "2.4" this means the system call probably appeared in a Linux 2.3.x kernel version, and first appeared in a stable kernel with Linux 2.4.0. (Development of the Linux 2.4 kernel was initiated from a branch of Linux 2.2.8 via the Linux 2.3.x unstable kernel series.)

•

Where a system call is marked "2.6" this means the system call probably appeared in a Linux 2.5.x kernel version, and first appeared in a stable kernel with Linux 2.6.0. (Development of Linux 2.6 was initiated from a branch of Linux 2.4.15 via the Linux 2.5.x unstable kernel series.)

•

Starting with Linux 2.6.0, the development model changed, and new system calls may appear in each Linux 2.6.x release. In this case, the exact version number where the system call appeared is shown. This convention continues with the Linux 3.x kernel series, which followed on from Linux 2.6.39; and the Linux 4.x kernel series, which followed on from Linux 3.19; and the Linux 5.x kernel series, which followed on from Linux 4.20; and the Linux 6.x kernel series, which followed on from Linux 5.19.

•

In some cases, a system call was added to a stable kernel series after it branched from the previous stable kernel series, and then backported into the earlier stable kernel series. For example some system calls that appeared in Linux 2.6.x were also backported into a Linux 2.4.x release after Linux 2.4.15. When this is so, the version where the system call appeared in both of the major kernel series is listed.

The list of system calls that are available as at Linux 5.14 (or in a few cases only on older kernels) is as follows:

On many platforms, including x86-32, socket calls are all multiplexed (via glibc wrapper functions) through socketcall(2) and similarly System V IPC calls are multiplexed through ipc(2).

Although slots are reserved for them in the system call table, the following system calls are not implemented in the standard kernel: afs_syscall(2), break(2), ftime(2), getpmsg(2), gtty(2), idle(2), lock(2), madvise1(2), mpx(2), phys(2), prof(2), profil(2), putpmsg(2), security(2), stty(2), tuxcall(2), ulimit(2), and vserver(2) (see also unimplemented(2)). However, ftime(3), profil(3), and ulimit(3) exist as library routines. The slot for phys(2) is in use since Linux 2.1.116 for umount(2); phys(2) will never be implemented. The getpmsg(2) and putpmsg(2) calls are for kernels patched to support STREAMS, and may never be in the standard kernel.

There was briefly set_zone_reclaim(2), added in Linux 2.6.13, and removed in Linux 2.6.16; this system call was never available to user space.

System calls on removed ports¶

Some system calls only ever existed on Linux architectures that have since been removed from the kernel:

AVR32 (port removed in Linux 4.12)

Blackfin (port removed in Linux 4.17)

Metag (port removed in Linux 4.17)

Tile (port removed in Linux 4.17)

Architecture-specific details: Alpha¶

getxgid(2)

returns a pair of GID and effective GID via registers r0 and r20; it is provided instead of getgid(2) and getegid(2).

getxpid(2)

returns a pair of PID and parent PID via registers r0 and r20; it is provided instead of getpid(2) and getppid(2).

old_adjtimex(2)

is a variant of adjtimex(2) that uses struct timeval32, for compatibility with OSF/1.

getxuid(2)

returns a pair of GID and effective GID via registers r0 and r20; it is provided instead of getuid(2) and geteuid(2).

sethae(2)

is used for configuring the Host Address Extension register on low-cost Alphas in order to access address space beyond first 27 bits.