NAME¶

faxaddmodem - configure a modem for use with HylaFAX

SYNOPSIS¶

/usr/sbin/faxaddmodem [ -s speed ] [ -f ] [ -nointeractive ] [ -skel=file ] [ tty ]

DESCRIPTION¶

faxaddmodem is an interactive shell script that does the necessary setup work to configure a modem for use by the HylaFAX software. To enable use of the configured modem one must either use the faxmodem(8C) program or configure the init(8C) program to startup a faxgetty(8C) process for the newly configured modem. In either case the faxq(8C) program must also be running if outbound services are to be provided.

If the serial port name is not specified on the command line faxaddmodem will prompt for it.

The configuration work done by faxaddmodem falls into two main areas: creating the necessary files to run a facsimile server process, and defining the contents of the configuration database file. The hylafax-config (5F) manual page has an in-depth description of the contents of the configuration file and should be consulted when installing a modem.

Many aspects of configuring a modem are operating system-specific; faxaddmodem uses a collection of support routines and parameters that are generated by the faxsetup(8C) program. If faxsetup has not been run on a machine prior to running then faxaddmodem will abort.

faxaddmodem can be used to install a new modem or re-configure an existing modem. In the latter case it will propagate all the server-related configuration parameters from the existing configuration file to the new configuration file. These parameter include items such as the phone number, area code, and tracing control parameters. Modem-related configuration parameters are, however, not propagated. Instead faxaddmodem deduces the type of modem attached to the specified serial port and then sets up the configuration parameters using a set of prototype configuration files that have been tested with like modems. If a modem is to be installed for which there is no existing prototype file, faxaddmodem will work from a comprehensive template of parameters that can be edited either during or after the installation process.

faxaddmodem deduces the type of modem attached to the serial port by sending commands to the modem at a fixed speed. By default, this speed is deduced by sending commands to the modem at successively decreasing speeds until a valid response is received. Alternatively, a fixed speed can be specified from the command line with the -s option.

Because faxaddmodem needs to read and write the modem that is to be installed it will not proceed with an installation if the modem is locked for use by another process. If the modem is not locked and the -f option is used, then the system's fuser(1) command will be invoked to ensure that faxaddmodem is the only process using the modem.

Finally, note that an installation can be safely aborted at any time by hitting the interrupt key. faxaddmodem delays making installation-related changes until after everything has been setup.

OPTIONS¶

-s speed

Communicate with the modem at a fixed speed; this may be any value recognized by the stty(1) command.

-f

Use the fuser(1) command for exclusive access to the device.

-nointeractive

Do not prompt for any input whenever a default option is available.

-skel=file

Use file as the skeleton configuration file (used when there is no existing modem config file).

PROTOTYPE CONFIGURATION FILES¶

faxaddmodem uses prototype configuration files that have been created for known modems. These prototype files are kept in the config subdirectory and, by convention, have names that identify a brand or type of modem and the DTE-DCE flow control scheme the prototype files configures. The faxaddmodem(8C) program that is used to configure a modem for use with HylaFAX selects a prototype configuration file using information retrieved from the modem and comments embedded in the prototype files. For Class 1 and Class 1.0 modems the product ID code returned by the command ``ATI0'' and the response from the command ``ATI3'' are used to select a prototype configuration file, while for Class 2 modems the manufacturer and model as returned by ``AT+FMFR?'' and ``AT+FMDL?'', respectively, are used (or ``AT+FMI?'' and ``AT+FMM?'' for Class 2.0 and Class 2.1 modems).

A Class 1 prototype configuration file is identified for use by faxaddmodem by searching for a comment of the form:

# CONFIG:CLASS1:144:.*:RTSCTS: Manufacturer='AT&T' Model=Dataport

Class 2, 2.0, and 2.1 prototype configuration files match the string ``manufacturer-model-flowcontrol'' against a sh(1) glob pattern specified in the configuration file, where manufacturer and model are the strings returned by querying the modem and flowcontrol is either ``RTSCTS'' for hardware flow control or ``XONXOFF'' for software flow control. For example:

# CONFIG: CLASS2: ZyXEL*-RTSCTS
# CONFIG: CLASS2.0: USRobotics*-XONXOFF

are configuration comments that appear in the prototype file for a ZyXEL 1496E with Class 2 support, and for a US Robotics Courier modem with Class 2.0 firmware.

The faxaddmodem program merges server-specific configuration parameters into a prototype configuration according to comments placed in the prototype file. All lines between ``BEGIN-SERVER'' and ``END-SERVER'' comments are placed with the appropriate server configuration parameters. Note that this means modem-related configuration parameters must be placed outside this area of the file.

FILES¶

/var/spool/hylafax/etc/setup.cache	master configuration parameters
/var/spool/hylafax/etc/setup.modem	modem-related configuration support
/var/spool/hylafax/config	prototype configuration files
/usr/sbin/ondelay	program to open device without waiting for carrier
/usr/sbin/lockname	SVR4 UUCP lockfile name generator

Consult hylafax-server(5F) for a complete discussion of the structure and content of the spooling area.

SEE ALSO¶

hylafax-server(5F), hylafax-config(5F), faxsetup(8C), faxq(8C), faxgetty(8C), faxmodem(8C), faxconfig(8C), faxsend(8C)