MEANWELL_NTU(8)

NUT Manual

MEANWELL_NTU(8)

NAME¶

meanwell_ntu - Driver for Mean Well NTU series inverter/UPS units

SYNOPSIS¶

meanwell_ntu -h

meanwell_ntu -a UPS_NAME [OPTIONS]

Note

This man page documents the hardware-specific features of the meanwell_ntu driver. For general information about NUT drivers, see nutupsdrv(8).

DESCRIPTION¶

The meanwell_ntu driver provides support for Mean Well NTU series inverter/UPS units that implement the vendor’s ASCII serial protocol.

This driver is currently experimental and intended for early adopters. Reported variables and behavior may evolve as additional models and firmware revisions are tested.

SUPPORTED HARDWARE¶

The driver is known to work with the following NTU models:

•NTU-1200

•NTU-1700

•NTU-2200

•NTU-3200

Supported DC-voltage variants include:

•NTU-1200-112, -124, -148

•NTU-1700-112, -124, -148

•NTU-2200-112, -124, -148

•NTU-3200-212, -224, -248

Other NTU-series devices using the same protocol may also work.

Communication uses a 9600-8-N-1 serial connection via RS-232 or a USB-serial adapter seen by the operating system as a serial port, e.g. /dev/ttyUSB0 (on Linux).

CABLES¶

MEAN WELL p/n: RJ11-RS232

A straight-through serial cable (no modem control) is required.

USB-to-RS-232 adapters work as long as they expose a standard TTY device.

CONFIGURATION¶

The driver is configured via ups.conf(5).

A minimal configuration:

[meanwell-ntu]


    driver = meanwell_ntu


    port   = /dev/ttyUSB0


    desc   = "Mean Well NTU-1200-124"

Required parameters¶

Example standard parameters:

driver

Must be set to meanwell_ntu.

port

The serial/USB tty device (e.g. /dev/ttyS0, /dev/ttyUSB0).

Optional parameters¶

This driver currently relies only on standard NUT parameters:

pollinterval

Interval between status polls (default: 2 seconds).

synchronous

Serial I/O mode as documented in nutupsdrv(8).

INSTANT COMMANDS¶

The following instant commands are supported when the connected hardware implements them (see upscmd(8)):

load.off

Request shutdown of inverter output and load power-off (vendor command C100000000000000).

load.on

Request inverter output power-on (vendor command C010000000000000).

Support varies across firmware revisions; test before relying on them.

STATUS AND VARIABLES¶

The driver regularly sends the Q (status) and I (info) commands and maps their fields to standard NUT variables.

Selected read-only variables¶

battery.voltage

Battery/DC bus voltage (V).

battery.charge

Remaining capacity (%).

battery.alarm.voltage

Low-voltage alarm threshold (V).

battery.shutdown.voltage

Low-voltage shutdown threshold (V).

input.voltage

Utility AC input voltage (non-zero in line or bypass mode).

output.voltage

Inverter output voltage (V).

output.frequency

Output frequency when running on battery (Hz).

ups.temperature

Inverter temperature (°C).

ups.load

Approximate load percentage, derived from PPP bits.

device.mfr

Manufacturer string (typically MEANWELL).

device.model, ups.model

Model descriptor (e.g. NTU-1200-124).

device.serial

Serial number when reported.

device.firmware

Firmware revision string.

UPS status flags¶

The NTU protocol exposes a 19-bit status word.

The driver maps selected bits into ups.status keywords:

On battery / inverter mode.

BYPASS

Bypass mode active.

Utility present / online.

Battery low.

OVER

Over-temperature condition.

The raw bit fields are also exported as informational variables such as battery.low, utility.present, bypass.mode, overtemp, etc.

LIMITATIONS¶

This driver is marked experimental:

•Protocol interpretation based on limited test samples.

•Some fields in Q/I responses are currently unused.

•Load and capacity reporting may be refined with further testing.

•Shutdown and restart behavior is basic and may not integrate with all NUT power-path logic.

For debugging, run the driver with high verbosity, e.g.:

/usr/local/ups/bin/meanwell_ntu -DDDDD -a meanwell-ntu

Please include model, firmware version, and operating mode details when reporting issues.

IMPLEMENTATION¶

Note the protocol on surface seems related to Megatec Qx, but is sufficiently different to warrant a separate driver and not a sub-driver of e.g. nutdrv_qx(8).

AUTHOR¶

The meanwell_ntu driver was contributed by Jonathan Hite.

Additional improvements may be provided by the NUT community. See the project repository for revision history.